Porsche Remote Lock and Unlock Stopped Working? PAS Fix
Why your Porsche remote stopped locking and unlocking
On water-cooled 911s and Boxster / Cayman models, the remote doesn't do much without the PAS. The PAS is the car's immobilizer and alarm unit. It holds the key data and talks to the engine computer. So when the remote stops locking and unlocking, the cause could be as simple as a dead fob battery, or it could be a failing PAS. If the remote quits and the car also won't start or won't recognize its keys, the PAS becomes a strong suspect. Check the simple things first. If the PAS turns out to be the problem, we can clone your original unit into a replacement by mail, so the car, engine computer and keys all match again.
Rule out the easy causes first
Before you blame a module, work through the basics. Many "dead remote" complaints turn out to be something small:
- Fob battery. A weak battery is the most common reason a remote stops working. Replace it and try again before anything else.
- One key or all of them? If the spare works and the main key doesn't, the problem is probably the key itself, not the car.
- Mechanical locking. If the doors won't lock from the key in the door or the interior switch either, look at the locking hardware and wiring before the alarm side.
- Battery and charging. Low system voltage can cause strange electrical behavior on these cars. Make sure the car's battery is healthy.
- Water in the cabin. Water getting into the interior is a known cause of electronics damage on these models. If the car has had a wet floor, take that seriously.
If none of that fixes it, especially if the remote problem shows up along with a no-start, a key that isn't recognized, or alarm faults, the PAS is worth a closer look.
What the PAS does
The PAS is the immobilizer and alarm unit on water-cooled 911 and Boxster / Cayman models. It stores the data that tells the car which keys belong to it, and it shares that information with the engine computer. When the PAS sees a key it knows, it gives the engine computer the go-ahead to start.
When a PAS fails, the usual result is that the car won't start or won't recognize its keys. Remote and alarm trouble can show up alongside those symptoms, because they all run through the same unit.
Why a replacement has to be cloned
You can't just bolt in a used PAS from another car. A donor unit still holds the key data and engine computer pairing from the car it came out of. Put it in your car and it won't recognize your keys or match your engine computer. The car still won't start.
Cloning solves that. We copy the data from your original PAS into the replacement, so the new unit matches your car, your engine computer and your keys. Your keys keep working, and you don't have to re-pair a stack of parts. The same idea applies on the engine side, which is why a swapped engine computer that was never matched to the car often leads to an immobilizer light after an ECU swap.
Porsche models we cover
These models use a PAS unit we can replace by mail:
| Model | Years |
|---|---|
| 911 (996) | 1999–2004 |
| 911 (997) | 2005–2012 |
| Boxster / Cayman (986 / 987) | 1997–2012 |
| Boxster / Cayman (981) | 2013–2016 |
| Carrera GT | 2004–2007 |
Don't see your car? Call 908-777-5741 and we'll check.
Pricing: send a donor or use ours
There are two ways to do the job. Both are listed on our Porsche PAS replacement page:
- $695: Program your donor PAS unit. You send your original PAS plus a donor unit, and we clone your data into the donor.
- $1,795: Tested used PAS unit from us, programmed to your car. You send your original PAS, and we supply the replacement.
Everything is programmed and tested on the bench before it ships back to you. Shipping is paid both ways by the customer. Return shipping is added to your invoice at cost, and you can choose ground, 2-day or overnight.
Confirm the failed module before you order
We can't diagnose a car by mail. You or your shop need to confirm that the PAS is the failed part before sending anything. A good scan tool, a check of the remote and the car's battery, and a look at the wiring will save you time and money. If the remote is the only problem and the car starts and runs normally, rule out the key itself before pulling the PAS.
How mail-in service works
Our process is built for repair shops, and it's open to owners too. We work with customers in all 50 states:
- Look up your vehicle on our website.
- Send a request with the VIN and the PAS part number.
- Pay the invoice. We confirm the job by VIN and part number before anything goes in the mail.
- Ship the module with the packing slip. Include the donor unit if you're using one.
- Plug it back in when it comes back.
Most jobs ship back within 1 to 3 business days of arriving. Because the PAS is immobilizer work, we need proof of ownership: registration plus photo ID, or a shop work order.
Every repair, programming and cloning job has a 3-month warranty. If we can't fix a module, we send it back and refund the service charge. You pay return shipping and a $95 bench-test fee.
Please note that we don't do immobilizer deletes. The goal is always a working, matched immobilizer, not a bypass.
If your diagnosis points to the engine computer instead of the PAS, see our ECU replacement and cloning service.
Frequently asked questions
Will my existing keys still work after the PAS is replaced?
Yes. We clone your original PAS, so the replacement holds the same key data and matches your car, engine computer and keys.
Can I just install a used PAS from a salvage car?
Not by itself. A used unit is still matched to the car it came from, so your car won't recognize your keys. Send it to us as a donor and we'll program it to your car for $695.
My remote doesn't work but the car starts fine. Is it the PAS?
Maybe, but check the fob battery, try your spare key, and confirm the locks work by other means first. We can't diagnose by mail, so please have the failed module confirmed before you ship it.
Ready to get your Porsche locking again?
Once you or your shop have confirmed the PAS has failed, send us your VIN and PAS part number to start a PAS order. Questions first? Call 908-777-5741 (Mon to Fri, 9am to 6pm) or email sales@duvallsautolab.com.
