GranTurismo Key Fob Not Working After Battery Change
Why your GranTurismo fob stopped working after a new battery
If your Maserati GranTurismo key fob buttons stopped working right after you changed the battery, the cause is almost always in the fob. The usual suspects are the wrong battery, a battery put in upside down or not fully seated, a bent or dirty contact tab, or a circuit board that got damaged when the case was pried open. The car itself is rarely at fault when the problem shows up right after a battery swap. Check the fob first. Only look at the car's body computer (the NBC) if your other key acts up too, or if the car starts showing other body or immobilizer problems.
Below are the likely causes, in order, and how to work out which part is at fault.
Likely causes, most common first
1. Wrong battery or a weak new battery. Compare the code printed on the new battery with the one you took out. A battery that looks similar but is a different size can sit loose and lose contact. Cheap or old stock can also be weak right out of the package. If you can, test it with a meter.
2. Battery upside down or not seated. Coin cells only work one way round. Check which side faces the positive contact, and make sure the battery sits flat under its retaining tab and doesn't move when you shake the fob.
3. Bent, loose or dirty contacts. The small metal tabs that touch the battery can get pushed flat or bent out of place during a swap. If a tab no longer presses firmly on the battery, the fob gets no power or only works now and then. Fingerprints and corrosion on the contacts cause the same thing.
4. Damage from opening the case. Prying the shell apart can crack the circuit board, knock off a tiny part or break a solder joint, especially at the battery holder. Look closely at the board under good light, ideally with a magnifier.
5. Worn buttons or a misaligned membrane. If the rubber button pad shifted when the case was closed, pressing a button might not reach the contact under it. Open the fob, reseat the pad and close it evenly.
6. Remote needs to be re-synced. On some vehicles a fob can lose sync with the car after it loses power. Whether this applies to your car and fob, and how to re-sync it, depends on the exact model year and setup. Check your owner's manual or ask a Maserati-savvy shop before you assume the fob is dead.
How to confirm which part is at fault
Work through these checks before you buy anything:
- Try the second key. If the other fob locks and unlocks the car normally, the car side is working and the problem is in the fob you opened.
- Swap batteries between fobs. Putting a battery you know is good into the problem fob rules out a bad cell.
- See if the car still starts on that key. Starting and remote buttons are separate functions. If the car starts on the key but the buttons do nothing, the fault is probably limited to the remote side of the fob.
- Have a shop test the signal. A shop with an RF key tester can tell you in seconds whether the fob is transmitting at all when you press a button.
- Look for other symptoms. If both keys stopped working at once, or the car is having trouble starting, failing to recognize keys, or losing body functions such as locks and lights, the problem may not be the fob. That's when the car's body computer is worth a look.
We can't diagnose a car by mail. You or your shop need to identify the failed part before you send anything.
What the NBC does, and when it's the real problem
Ferrari-engined Maserati models, including the GranTurismo (2008–2019), use the NBC as their body computer. It runs body functions and holds the immobilizer data that lets the car recognize its keys. When an NBC fails or takes on water, the car can stop starting or lose body functions.
So a dead fob on its own, right after a battery change, almost never points to the NBC. If the diagnosis does point there (both keys rejected, a no-start, missing body functions, or water damage), that's where we come in.
Why a replacement NBC has to be cloned
A new or used NBC doesn't know your car or your keys. Your keys are paired with the immobilizer data stored in your original unit. Install a blank or mismatched NBC and the car won't recognize the keys you have. For more on that, see our guide on a replacement Maserati NBC that won't work with the original keys.
With our Maserati NBC replacement service, you send us your original NBC and we transfer your car's data into a replacement. The immobilizer data carries over, so the car starts on the keys you already have and there are no new keys to buy or program. Each replacement is programmed and tested on the bench before it ships back.
NBC replacement starts from $1,250. Pricing goes by your NBC part number, and we confirm the price before you ship anything. We also cover the GranCabrio (2010–2019), Quattroporte V (2004–2012), Coupe/Spyder 4200 (2002–2007) and 3200 GT (1998–2002). If you have a Ferrari, see Ferrari NBC replacement.
How mail-in service works
- Look up your vehicle on our website.
- Send a request with your VIN and NBC part number.
- Pay the invoice.
- Ship the module with the packing slip.
- Plug it back in when it comes back.
Nothing ships until we've confirmed the job by VIN and part number. Most jobs ship back within 1 to 3 business days of arriving. You pay shipping both ways, and return shipping (ground, 2-day or overnight) is added to the invoice at cost. Because this is immobilizer work, we need proof of ownership: registration plus photo ID, or a shop work order. Every job has a 3-month warranty. If we can't fix a module, we send it back and refund the service charge. In that case you pay return shipping and a $95 bench-test fee.
We work with repair shops and owners in all 50 states.
Frequently asked questions
Will replacing the NBC fix my key fob buttons?
Only if the NBC is actually the failed part. If the buttons quit right after a battery change and your other key works fine, the problem is in the fob, and a new NBC won't fix it.
Do I need new keys after an NBC replacement?
No. We carry the immobilizer data from your original NBC into the replacement, so the car starts on the keys you already have.
What do I need to send?
Your original NBC with the packing slip, after you've sent your VIN and part number and paid the invoice. Include proof of ownership or a shop work order.
If your shop has confirmed the NBC is at fault, request an NBC quote, call 908-777-5741 (Mon to Fri, 9am to 6pm), or email sales@duvallsautolab.com to start your order.
