Duvall's Auto LabClinical Care
for Modern Machines

BMW Module Programming or Clone by Mail: FRM3, ICM, EPS

Can a BMW module be cloned or programmed by mail?

Yes. If your BMW has a failed or replacement FRM3 footwell module, LCM light module, ICM chassis module, power steering (EPS) module, EDC/VDP suspension module or VTG transfer case module, you can mail it to us. We clone the data from your original unit onto the replacement, or program the replacement to your VIN, and ship it back ready to plug in. Module programming or cloning starts from $175, and the exact price for your car shows up in the vehicle lookup on the Duvall's Auto Lab home page. Before you order, please confirm which module has failed. We can't diagnose a car by mail, so you or your shop need to pin it down first.

Why BMW modules need cloning or programming

A BMW isn't one computer. It's a network of control modules, and each one stores data tied to that specific car: the VIN, how the car is equipped, coding, and sometimes calibration values. If you install a used module from another car, or a new one straight off the shelf, it usually won't work right. It may do nothing at all, set fault codes, or act like it belongs to a different car.

You can fix this two ways:

  • Cloning copies the stored data from your original module onto the replacement. The car then treats the replacement as the same module it always had. This works best when the old unit failed but its memory can still be read.
  • Programming writes your car's VIN and the correct setup to the replacement module. This is the route when the original can't be read, or when you have no module to send at all.

The BMW modules we cover

Here is what we handle on each platform:

  • FRM3 (footwell module): 1-Series E82/E87/E88, 3-Series E90–E93, 5-Series E60/E61, 6-Series E63/E64, plus the F10/F11 5-Series, F07 5-Series GT, F12/F13 6-Series and F06 Gran Coupe. The FRM runs exterior lights and other body functions. A well-known way it fails is losing its data after low voltage, like a dead battery, a jump start or a battery swap. Afterward the lights or windows may stop working.
  • LCM (light check module): 3-Series E36 (1998) and E46, 5-Series E39, 7-Series E38. These older cars use the LCM for lighting control and bulb monitoring.
  • ICM (Integrated Chassis Management): 1-Series F20/F21, 2-Series F22/F23, 3-Series F30/F31, 3-Series GT F34, 4-Series F32/F33/F36, and the F10/F11, F07, F12/F13 and F06 platforms.
  • Power steering (EPS): most F- and G-series cars, including the F20/F21, F22/F23, F44, F45/F46, U06, G42, F30/F31, F34, F32/F33/F36, G20/G21, G22/G23/G26, G30/G31 and G60.
  • EDC / VDM / VDP suspension: where fitted, on the F10/F11, F07, F12/F13 and F06, and on the G42, G20/G21, G22/G23/G26, G30/G31 and G60.
  • VTG transfer case module: xDrive cars only, on the G42, G20/G21, G22/G23/G26, G30/G31 and G60.

If your model or module isn't listed, look it up on our website or email us before you ship anything.

Confirm the failed module first

Please do this before ordering. BMW faults can fool you. Lights that won't work could be the FRM, a wiring problem or a bad switch. A steering or suspension warning could come from a sensor and not the module. Have a good BMW scan tool read the car, or have your shop do it, and make sure the module itself is the problem. We can only fix or program the part you send us. We don't diagnose cars remotely.

What to send us

When you place the request, we'll need:

  1. The full VIN of the car.
  2. The module part number from the label on the unit.
  3. The module itself. Send your original if you're cloning, and the replacement too if you already have one. If you don't have a replacement or have nothing to send, we can source a programmed replacement unit for you.

Nothing ships until we've confirmed the job by VIN and part number. That keeps you from paying for work on the wrong part.

How mail-in service works

We're a mail-in lab in Columbia, NJ. We don't take walk-ins, and we serve shops and owners in all 50 states.

  1. Look up your vehicle on duvallsautolab.com to see your exact price.
  2. Send a request with the VIN and module part number.
  3. Pay the invoice.
  4. Ship the module with the packing slip we give you.
  5. Plug it back in once it comes back.

Most jobs ship back within 1 to 3 business days after they arrive. You pay shipping both ways. Return shipping is added to your invoice at cost, and you can choose ground, 2-day or overnight. Every repair, programming and cloning job comes with a 3-month warranty.

If we can't fix a module, we send it back and refund the service charge. In that case you pay return shipping plus a $95 bench-test fee.

Other BMW work we do: see our BMW ABS / DSC module repair page. If the engine computer is the problem, read about ECU replacement and cloning.

Frequently asked questions

How much does BMW module cloning or programming cost?

It starts from $175. The exact price depends on the car and the module, and it shows up when you look up your vehicle on our home page.

Can I use a used module from a junkyard or eBay?

Often, yes. That's a common reason people clone or program a module. Make sure the replacement's part number is compatible with your car, and include both part numbers in your request so we can confirm the job before you ship.

My FRM3 died after a battery change. Can it be saved?

Often it can. Low voltage is a common way FRM3 modules lose their data. Send us the module and we'll check whether it can be recovered or whether you need a cloned or programmed replacement. If we can't fix it, the refund terms above apply.

Ready to get your BMW back on the road? Look up your vehicle and start an order, call us at 908-777-5741 (Mon to Fri, 9am to 6pm), or email sales@duvallsautolab.com.

Start an order Call 908-777-5741